<

CCIE notes – Security part 2

Layer 3 Security

 

Recommendation
1. Enable secure Telnet access to a router and use SSH
2. Enable SNMP security, adding SNMPv3 support
3. Turn off unnecessary services on the router platform
4. Turn on logging to provide on audit trail
5. Enable protocol authentication
6. Enable CEF

 

General Layer3 Security Considerations

1. Smurf Attacks

– a large number of ICMP Echo Requires with same typical IP address in the packet
– the destination address is a subnet broadcast address, also known as a direct broadcast address

Solutions

1.no ip directed-broadcast” – by default in IOS version 12.0
– prevents the router from forwarding the broadcast onto the VLAN
2. Unicast Reverse Path Forwarding (uRPF)
– tells cisco IOS to examine the source IP address of incoming packets on that itnerface (CEF must be enabled)
Two Types:
a. Strict RPF – the router checks if the matching route uses an outgoing interface, that is the same interface on which the packet was received, in not => discarded
b. Loose RPF – the router checks for an y route that can be used to reach the source IP address

 

2. TCP Syn flood, the Established Bit and TCP Intercept

TCP Syn flood – creates connections
– “established” ACL can be used, when you only want to open from te inside towards outside
– TCP “intercept” can be used when you want the connections to come from “putside” towards “inside”

TCP “intercept” works in 2 ways:
1. Watch mode – keeps state information about TCP connections that match a defined ACL
– if a TCP connection does not complete the three-way handshake within a particular time period, it send a TCP reset to the servers
– it also count the number of new connections over time, and if a large number (default 1000), the router temporarily filters new TCP requires to prevent a SYN attack
2. Intercept mode – router applies to TCP connection requirements instead of forwarding them to the actual server

 

Classic Cisco IOS firewall

CBAC – Context-Based Access Control
– you must configure the following:
1. Protocol to inspect
2. Interface on which to perform the inspection
3. Direction of the traffic to inspect, per interface

TCP vs UDP with CBAC
– TCP has clear-cut connections, so CBAC can handle it easy
– UDP more difficult  to handle

Common protocol that CBAC can Inspect:
1. Any TCP
2. Any UDP sessions
3. FTP
4. SMTP
5. TFTP
6. H.323
7. Java
8.

 

CBAC Disadvantages

– CBAC comes after ACL filters
– CBAC cannot protect against attacks that are coming from inside
– CBAC works only on protocol you set to “inspect”
– to inspect other types of traffic (not TCP or UDP), you must configure a named inspection tool
– CBAC does not inspect traffic generated from itself
– CBAC has restrictions on handling encryption traffic

 

Cisco IOS Zone-Based Firewalls

– traffic can travel between the interfaces of the same zone, but not between zones
– zones are configured using Class-Based Policy (like MQC)
– can inspect: HTTP, HTTPS, SMTP, ESMTP, POP3, IMAP, Yahoo IM, MSN, RPC and P-2-P application

Steps to configure ZBF
1. Create zones
2. Decide how traffic should travel between the zones and create zone-pairs on the router
3. Create class-maps to identify inter-zone traffic that must be inspected by the firewall
4. Assign policies to the traffic by creating policy maps and associated class-maps with them
5. Assign policy maps to the appropriate zone-pair
6. Assign interfaces to zone. An interface may be assigned to only one security zone

 

Cisco IOS IPS

– it provides Deep Packet Inspection (DPI) of traffic transiting the router
– the signature are on flash
– when IPS is configurate, it acts like an inline IPS

Steps
1. Remove all signature category and then import the basic IOS IPS category
2. Create a directory in flash to store the IPS configuration
3. Create an IOS IPS rule
4. Specify the location of the signature
5. Apply the rule to an interface, inbound and/or outbound
6. Once rule applied, the router loads the signature
7. Verify “IPS using: “#show ip ips config”

 

Control-Plane Policing (CoPP)

– affects the traffic coming to the router
– addresses this problem by leveraging the MQC to rate-limit or drop control-plane traffic
– used so you do not get locked out

Implementing CoPP:
1. Enable QoS globally; else CoPP is done in software and not HW
2. Create the ACL to classify traffic
3. Create class-map and match the appropriate ACL or either IP Precedence or DSCP values
4. Create a Policy Map and associate the class-maps with it
5. Assign allowed bandwidth
6. Assign the policy map to the router or switch control plane as a service policy

 

Dynamic Multipoint VPN (DM-VPN)

– uses IPSEC, GRE, Next Hop Resolvation Protocol (NHRP)
– supports segmentation across VPNs and is VRF-aware
– the HUB router is configured for a single multipoint GRE (mGRE) and a set of profiles applied to the spoke routers

DMVPN vs Hub-Spoke VPN – DMVPN advantages:
1. Simpler Hub configuration. A DMVPN hub router requires only one multipoint GRE tunnel interface, one IPSEC profile and no crypto ACL
2. Zero-touch at the hub router for prvisioning spoke routers. The hub router does not require configuration when new spoke router are brought online
3. Automatically initiated IPSec encrypt, fac by NHRP
4. Dynamic addressing support for spoke routers. Instead of static configuration, the hub learns spoke router addresses when they requires to the network
5. Dynamic created spoke-to-spoke tunnels. Spoke routers learn about each other using NHRP, so they can form tunnels between each other automatically instead of require spoke-to-spoke traffic to be encrypted
6. VRF integration for MPLS environment
A dynamic routing protocol (EIGRP, OSPF, BGP, RIP or even ODR) is required between the hub and the spokes.

You can skip to the end and leave a response. Pinging is currently not allowed.

3 Responses to “CCIE notes – Security part 2”

  1. Mark says:

    I see a lot of interesting posts on your blog. You have to spend a lot of
    time writing, i know how to save you a lot of time, there is a tool that creates unique, google friendly posts in couple of
    seconds, just type in google – k2 unlimited content

  2. Pretty nice post. I just stumbled upon your weblog and wished to say that I have really
    enjoyed surfing around your blog posts. After all I’ll
    be subscribing to your feed and I hope you write again very soon!

  3. Thanks in favor of sharing such a fastidious idea, article
    is nice, thats why i have read it fully

Leave a Reply